444 lines
12 KiB
C
444 lines
12 KiB
C
/* USER CODE BEGIN Header */
|
|
/**
|
|
******************************************************************************
|
|
* @file : stm32f407vet6_board.c
|
|
* @brief : STM32F407VET6 board configuration implementation
|
|
******************************************************************************
|
|
*/
|
|
/* USER CODE END Header */
|
|
|
|
#include "bsp_board.h"
|
|
#include "bsp_config.h"
|
|
#include "hal_gpio.h"
|
|
#include "hal_uart.h"
|
|
#include "hal_spi.h"
|
|
|
|
/**
|
|
* @brief Default LED initialization function
|
|
* @param config: LED configuration structure
|
|
* @retval HAL status code
|
|
*/
|
|
static hal_ret_t default_led_init(const void* config) {
|
|
const bsp_led_config_t* led_config = (const bsp_led_config_t*)config;
|
|
hal_gpio_config_t gpio_config = {
|
|
.port = led_config->port,
|
|
.pin = led_config->pin,
|
|
.mode = led_config->mode,
|
|
.speed = led_config->speed,
|
|
.pull = led_config->pull
|
|
};
|
|
return hal_gpio_configure_pin(&gpio_config);
|
|
}
|
|
|
|
/**
|
|
* @brief Default button initialization function
|
|
* @param config: Button configuration structure
|
|
* @retval HAL status code
|
|
*/
|
|
static hal_ret_t default_button_init(const void* config) {
|
|
const bsp_buttons_config_t* buttons_config = (const bsp_buttons_config_t*)config;
|
|
uint8_t i;
|
|
hal_ret_t status = HAL_RET_OK;
|
|
|
|
for (i = 0; i < buttons_config->count; i++) {
|
|
const bsp_button_config_t* button_config = &buttons_config->buttons[i];
|
|
hal_gpio_config_t gpio_config = {
|
|
.port = button_config->port,
|
|
.pin = button_config->pin,
|
|
.mode = button_config->mode,
|
|
.speed = button_config->speed,
|
|
.pull = button_config->pull
|
|
};
|
|
status = hal_gpio_configure_pin(&gpio_config);
|
|
if (status != HAL_RET_OK) {
|
|
break;
|
|
}
|
|
}
|
|
|
|
return status;
|
|
}
|
|
|
|
/**
|
|
* @brief Default UART initialization function
|
|
* @param config: UART configuration structure
|
|
* @retval HAL status code
|
|
*/
|
|
static hal_ret_t default_uart_init(const void* config) {
|
|
const bsp_uart_config_t* uart_config = (const bsp_uart_config_t*)config;
|
|
hal_uart_config_t uart_cfg = {
|
|
.instance = (hal_uart_instance_t)uart_config->instance,
|
|
.baudrate = uart_config->baudrate,
|
|
.parity = uart_config->parity,
|
|
.stopbits = uart_config->stopbits,
|
|
.databits = uart_config->databits
|
|
};
|
|
return hal_uart_config(&uart_cfg);
|
|
}
|
|
|
|
/**
|
|
* @brief Default SPI initialization function
|
|
* @param config: SPI configuration structure
|
|
* @retval HAL status code
|
|
*/
|
|
static hal_ret_t default_spi_init(const void* config) {
|
|
const bsp_spi_config_t* spi_config = (const bsp_spi_config_t*)config;
|
|
hal_spi_config_t spi_cfg = {
|
|
.instance = spi_config->instance,
|
|
.mode = spi_config->mode,
|
|
.baudrate = spi_config->baudrate,
|
|
.polarity = spi_config->polarity,
|
|
.phase = spi_config->phase,
|
|
.databits = spi_config->databits
|
|
};
|
|
return hal_spi_init(spi_config->instance, &spi_cfg);
|
|
}
|
|
|
|
/**
|
|
* @brief Default I2C initialization function
|
|
* @param config: I2C configuration structure
|
|
* @retval HAL status code
|
|
*/
|
|
static hal_ret_t default_i2c_init(const void* config) {
|
|
/* TODO: Implement default I2C initialization */
|
|
return HAL_RET_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Default CAN initialization function
|
|
* @param config: CAN configuration structure
|
|
* @retval HAL status code
|
|
*/
|
|
static hal_ret_t default_can_init(const void* config) {
|
|
/* TODO: Implement default CAN initialization */
|
|
return HAL_RET_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Default ADC initialization function
|
|
* @param config: ADC configuration structure
|
|
* @retval HAL status code
|
|
*/
|
|
static hal_ret_t default_adc_init(const void* config) {
|
|
/* TODO: Implement default ADC initialization */
|
|
return HAL_RET_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Default W25QXX initialization function
|
|
* @param config: W25QXX configuration structure
|
|
* @retval HAL status code
|
|
*/
|
|
static hal_ret_t default_w25qxx_init(const void* config) {
|
|
const bsp_w25qxx_config_t* w25qxx_config = (const bsp_w25qxx_config_t*)config;
|
|
hal_ret_t status = HAL_RET_OK;
|
|
|
|
/* Initialize CS pin */
|
|
hal_gpio_config_t gpio_config = {
|
|
.port = w25qxx_config->cs_port,
|
|
.pin = w25qxx_config->cs_pin,
|
|
.mode = HAL_GPIO_MODE_OUTPUT_PP,
|
|
.speed = HAL_GPIO_SPEED_HIGH,
|
|
.pull = HAL_GPIO_PULL_NO
|
|
};
|
|
status = hal_gpio_configure_pin(&gpio_config);
|
|
if (status != HAL_RET_OK) {
|
|
return status;
|
|
}
|
|
|
|
/* Deselect chip initially */
|
|
status = hal_gpio_write_pin(w25qxx_config->cs_port, w25qxx_config->cs_pin, HAL_GPIO_PIN_SET);
|
|
if (status != HAL_RET_OK) {
|
|
return status;
|
|
}
|
|
|
|
/* SPI instance is now just an index, actual SPI initialization is handled separately */
|
|
return status;
|
|
}
|
|
|
|
/**
|
|
* @brief STM32F407VET6 board button configurations
|
|
*/
|
|
static const bsp_button_config_t stm32f407vet6_buttons[] = {
|
|
/* KEY0 - PE4, active low */
|
|
{
|
|
.port = HAL_GPIO_PORT_E,
|
|
.pin = HAL_GPIO_PIN_4,
|
|
.mode = HAL_GPIO_MODE_INPUT,
|
|
.speed = HAL_GPIO_SPEED_LOW,
|
|
.pull = HAL_GPIO_PULL_UP,
|
|
.active_high = 0
|
|
},
|
|
/* KEY1 - PE3, active low */
|
|
{
|
|
.port = HAL_GPIO_PORT_E,
|
|
.pin = HAL_GPIO_PIN_3,
|
|
.mode = HAL_GPIO_MODE_INPUT,
|
|
.speed = HAL_GPIO_SPEED_LOW,
|
|
.pull = HAL_GPIO_PULL_UP,
|
|
.active_high = 0
|
|
},
|
|
/* WKUP - PA0, active high */
|
|
{
|
|
.port = HAL_GPIO_PORT_A,
|
|
.pin = HAL_GPIO_PIN_0,
|
|
.mode = HAL_GPIO_MODE_INPUT,
|
|
.speed = HAL_GPIO_SPEED_LOW,
|
|
.pull = HAL_GPIO_PULL_DOWN,
|
|
.active_high = 1
|
|
}
|
|
};
|
|
|
|
/**
|
|
* @brief STM32F407VET6 buttons configuration
|
|
*/
|
|
static const bsp_buttons_config_t stm32f407vet6_buttons_config = {
|
|
.enable = 1,
|
|
.count = sizeof(stm32f407vet6_buttons) / sizeof(bsp_button_config_t),
|
|
.buttons = stm32f407vet6_buttons
|
|
};
|
|
|
|
/**
|
|
* @brief STM32F407VET6 board UART configurations
|
|
*/
|
|
static const bsp_uart_config_t stm32f407vet6_uarts[] = {
|
|
/* USART1 - PA9(TX), PA10(RX) */
|
|
{
|
|
.enable = 1,
|
|
.instance = BSP_UART_INSTANCE_1,
|
|
.baudrate = 115200,
|
|
.parity = HAL_UART_PARITY_NONE,
|
|
.stopbits = HAL_UART_STOPBITS_1,
|
|
.databits = HAL_UART_DATABITS_8,
|
|
.tx_port = HAL_GPIO_PORT_A, /* USART1_TX - PA9 */
|
|
.tx_pin = HAL_GPIO_PIN_9,
|
|
.rx_port = HAL_GPIO_PORT_A, /* USART1_RX - PA10 */
|
|
.rx_pin = HAL_GPIO_PIN_10
|
|
}
|
|
};
|
|
|
|
/**
|
|
* @brief STM32F407VET6 board SPI configurations
|
|
*/
|
|
static const bsp_spi_config_t stm32f407vet6_spis[] = {
|
|
/* SPI1 - PA5(SCK), PA6(MISO), PA7(MOSI) */
|
|
{
|
|
.enable = 1,
|
|
.instance = HAL_SPI_INSTANCE_1,
|
|
.mode = HAL_SPI_MODE_MASTER,
|
|
.baudrate = 1000000, /* 1 MHz */
|
|
.polarity = HAL_SPI_POLARITY_LOW,
|
|
.phase = HAL_SPI_PHASE_1EDGE,
|
|
.databits = HAL_SPI_DATABITS_8,
|
|
.sck_port = HAL_GPIO_PORT_A,
|
|
.sck_pin = HAL_GPIO_PIN_5,
|
|
.miso_port = HAL_GPIO_PORT_A,
|
|
.miso_pin = HAL_GPIO_PIN_6,
|
|
.mosi_port = HAL_GPIO_PORT_A,
|
|
.mosi_pin = HAL_GPIO_PIN_7
|
|
}
|
|
};
|
|
|
|
/**
|
|
* @brief STM32F407VET6 board I2C configurations
|
|
*/
|
|
static const bsp_i2c_config_t stm32f407vet6_i2cs[] = {
|
|
/* I2C1 - PB6(SCL), PB7(SDA) */
|
|
{
|
|
.enable = 0, /* Disabled by default */
|
|
.instance = HAL_I2C_INSTANCE_1,
|
|
.speed = HAL_I2C_SPEED_STANDARD,
|
|
.address_mode = HAL_I2C_ADDRESS_7BIT,
|
|
.dutycycle = HAL_I2C_DUTYCYCLE_2,
|
|
.own_address1 = 0x00,
|
|
.scl_port = HAL_GPIO_PORT_B,
|
|
.scl_pin = HAL_GPIO_PIN_6,
|
|
.sda_port = HAL_GPIO_PORT_B,
|
|
.sda_pin = HAL_GPIO_PIN_7
|
|
}
|
|
};
|
|
|
|
/**
|
|
* @brief STM32F407VET6 board CAN configurations
|
|
*/
|
|
static const bsp_can_config_t stm32f407vet6_cans[] = {
|
|
/* CAN1 - PA11(RX), PA12(TX) */
|
|
{
|
|
.enable = 0, /* Disabled by default */
|
|
.instance = HAL_CAN_INSTANCE_1,
|
|
.mode = HAL_CAN_MODE_NORMAL,
|
|
.prescaler = 6, /* 168MHz / 6 = 28MHz */
|
|
.sync_jump_width = 1,
|
|
.time_segment1 = 13,
|
|
.time_segment2 = 2,
|
|
.rx_port = HAL_GPIO_PORT_A,
|
|
.rx_pin = HAL_GPIO_PIN_11,
|
|
.tx_port = HAL_GPIO_PORT_A,
|
|
.tx_pin = HAL_GPIO_PIN_12
|
|
}
|
|
};
|
|
|
|
/**
|
|
* @brief STM32F407VET6 board ADC channel configurations
|
|
*/
|
|
static const bsp_adc_channel_config_t stm32f407vet6_adc_channels[] = {
|
|
/* ADC1 Channel 0 - PA0 */
|
|
{
|
|
.enable = 0, /* Disabled by default */
|
|
.channel = HAL_ADC_CHANNEL_0,
|
|
.sampletime = HAL_ADC_SAMPLETIME_56CYCLES,
|
|
.rank = 1
|
|
}
|
|
};
|
|
|
|
/**
|
|
* @brief STM32F407VET6 board ADC configurations
|
|
*/
|
|
static const bsp_adc_config_t stm32f407vet6_adcs[] = {
|
|
/* ADC1 */
|
|
{
|
|
.enable = 0, /* Disabled by default */
|
|
.instance = HAL_ADC_INSTANCE_1,
|
|
.resolution = HAL_ADC_RESOLUTION_12B,
|
|
.scan_conversion_mode = 0,
|
|
.continuous_conversion_mode = 0,
|
|
.channel_count = sizeof(stm32f407vet6_adc_channels) / sizeof(bsp_adc_channel_config_t),
|
|
.channels = stm32f407vet6_adc_channels
|
|
}
|
|
};
|
|
|
|
/**
|
|
* @brief STM32F407VET6 board LED configurations
|
|
*/
|
|
static const bsp_led_config_t stm32f407vet6_leds[] = {
|
|
/* LED0 - PA6 */
|
|
{
|
|
.enable = 1,
|
|
.port = HAL_GPIO_PORT_A,
|
|
.pin = HAL_GPIO_PIN_6,
|
|
.mode = HAL_GPIO_MODE_OUTPUT_PP,
|
|
.speed = HAL_GPIO_SPEED_MEDIUM,
|
|
.pull = HAL_GPIO_PULL_NO
|
|
},
|
|
/* LED1 - PA7 */
|
|
{
|
|
.enable = 1,
|
|
.port = HAL_GPIO_PORT_A,
|
|
.pin = HAL_GPIO_PIN_7,
|
|
.mode = HAL_GPIO_MODE_OUTPUT_PP,
|
|
.speed = HAL_GPIO_SPEED_MEDIUM,
|
|
.pull = HAL_GPIO_PULL_NO
|
|
}
|
|
};
|
|
|
|
/**
|
|
* @brief STM32F407VET6 board configuration
|
|
*/
|
|
const bsp_board_config_t stm32f407vet6_board_config = {
|
|
.version = BSP_CONFIG_VERSION,
|
|
.name = "STM32F407VET6",
|
|
.description = "STM32F407VET6 Development Board",
|
|
.id = {
|
|
.vendor_id = 0x0483, /* STMicroelectronics */
|
|
.product_id = 0x374B, /* STM32F4 Series */
|
|
.serial_number = 0x00000001 /* Default serial number */
|
|
},
|
|
|
|
/* Board features */
|
|
.features = (
|
|
BSP_BOARD_FEATURE_LED |
|
|
BSP_BOARD_FEATURE_BUTTON |
|
|
BSP_BOARD_FEATURE_UART |
|
|
BSP_BOARD_FEATURE_SPI |
|
|
BSP_BOARD_FEATURE_I2C |
|
|
BSP_BOARD_FEATURE_CAN |
|
|
BSP_BOARD_FEATURE_ADC |
|
|
BSP_BOARD_FEATURE_W25QXX
|
|
),
|
|
|
|
/* Hardware information */
|
|
.hw_info = {
|
|
.clock_speed = 168000000, /* 168 MHz */
|
|
.flash_size = 512 * 1024, /* 512 KB */
|
|
.ram_size = 192 * 1024, /* 192 KB */
|
|
.eeprom_size = 0, /* No internal EEPROM */
|
|
.sram_size = 64 * 1024, /* 64 KB SRAM */
|
|
.cpu_core = 0x0F, /* Cortex-M4 */
|
|
.cpu_bits = 32 /* 32-bit CPU */
|
|
},
|
|
|
|
/* Peripheral configurations */
|
|
.leds = {
|
|
.enable = 1,
|
|
.count = sizeof(stm32f407vet6_leds) / sizeof(bsp_led_config_t),
|
|
.leds = stm32f407vet6_leds
|
|
},
|
|
.buttons = stm32f407vet6_buttons_config,
|
|
.w25qxx = {
|
|
.enable = 1,
|
|
.cs_port = HAL_GPIO_PORT_B,
|
|
.cs_pin = HAL_GPIO_PIN_0,
|
|
.spi_instance = 0 /* Use SPI instance 0 */
|
|
},
|
|
|
|
/* Peripheral arrays */
|
|
.periphs = {
|
|
/* UART configurations */
|
|
.uart_count = 1,
|
|
.uarts = stm32f407vet6_uarts,
|
|
|
|
/* SPI configurations */
|
|
.spi_count = 1,
|
|
.spis = stm32f407vet6_spis,
|
|
|
|
/* I2C configurations */
|
|
.i2c_count = 1,
|
|
.i2cs = stm32f407vet6_i2cs,
|
|
|
|
/* CAN configurations */
|
|
.can_count = 1,
|
|
.cans = stm32f407vet6_cans,
|
|
|
|
/* ADC configurations */
|
|
.adc_count = 1,
|
|
.adcs = stm32f407vet6_adcs
|
|
},
|
|
|
|
/* Initialization function pointers */
|
|
.init_funcs = {
|
|
.led_init = default_led_init,
|
|
.button_init = default_button_init,
|
|
.uart_init = default_uart_init,
|
|
.spi_init = default_spi_init,
|
|
.i2c_init = default_i2c_init,
|
|
.can_init = default_can_init,
|
|
.adc_init = default_adc_init,
|
|
.w25qxx_init = default_w25qxx_init
|
|
},
|
|
|
|
/* Additional board-specific configuration */
|
|
.custom_config = NULL,
|
|
.custom_config_size = 0,
|
|
|
|
/* Board revision information */
|
|
.major_rev = 1,
|
|
.minor_rev = 0,
|
|
.patch_rev = 0,
|
|
.revision_desc = "Original release"
|
|
};
|
|
|
|
/**
|
|
* @brief Get board name
|
|
* @retval Board name string
|
|
*/
|
|
const char* bsp_board_get_name(void) {
|
|
return stm32f407vet6_board_config.name;
|
|
}
|
|
|
|
/**
|
|
* @brief Get board configuration
|
|
* @retval Pointer to board configuration structure
|
|
*/
|
|
const bsp_board_config_t* bsp_board_get_config(void) {
|
|
return &stm32f407vet6_board_config;
|
|
}
|